<menuitem id="blhtj"><listing id="blhtj"></listing></menuitem>
        <track id="blhtj"></track>

        <noframes id="blhtj">
        <em id="blhtj"></em>

        <dl id="blhtj"><sub id="blhtj"><thead id="blhtj"></thead></sub></dl>
          <track id="blhtj"></track>

          <address id="blhtj"><big id="blhtj"></big></address>
          <noframes id="blhtj">

              <track id="blhtj"><big id="blhtj"><big id="blhtj"></big></big></track>
                  <noframes id="blhtj">

                  <video id="blhtj"><progress id="blhtj"><nobr id="blhtj"></nobr></progress></video>

                    1. 1
                    2. 2
                      Contact us

                      Fans Lighting Company Limited
                      Website:www.nnxwbj.com
                      Mail:sales@fanslighting.com
                      Address:No.1 Nanlong Road, Nanlian Community, Longgang District, Shenzhen 518116 China

                      LED Technology
                      Current Location:HOME > LED Technology
                      • Author: admin
                      • Source:
                      • Date: 2015-05-23
                      • Views: 4099Times

                      This article will give an introduction to installation for LED tube power supply in details.
                       

                      There are two modes of connection for LED tube power supply installation: single-end power input, two-end power input. Here are the steps:

                      Two-end power input Installation:

                       

                      LED Tube Light Wiring Diagram

                       

                       

                      Installation Instruction

                      1) Turn off the electricity supply before installation

                      2) For refitting old fluorescent lamp, with a two-end power-input LED tube, please re-connect your wire as the following diagram.

                       

                       

                      3) For diagram A1 loop with inductive ballast & starter, after removing the starter, LED 

                      tube can be installed directly into the G13 base. Then LED tube light is ready to work. And the loop has been changed from A1 to A2.
                       

                      Note: You can just keep the inductive ballast as it was. However, it’ll consumer some power. For saving energy, it’s still suggested to cut it out if your labor cost is not so high.

                       

                      4) For diagram B1 loop with electronic ballast , please remove the electronic ballast firs.Then connect L and N to the two sockets of the G13 base separately. Now your LED tube light is ready to be turned on. And the loop has been changed into the one showed in diagram B2.

                       

                      Single-end Power Input Installation:

                       

                       

                      LED Tube Light Wiring Diagram

                       

                       

                      Installation instructions

                      1) Turn off the electricity supply before installation .

                      2) For refitting old fluorescent lamp with a single-end power input LED tube, please re-connect your wire as the following diagram.

                       

                       

                      3)For diagram A1 loop with magnetic ballast & starter, please remove the starter first.Then connect line N and Line L to the same side socket but separately. Now you can put on the LED tube and turn it on. And the loop has been changed into the one as showed in diagram A2.

                       

                      Note: You can just keep magnetic ballast as it was. However, it’ll consumer some power. For saving energy, it’s still suggested to remove it if your labor cost is not so high.

                       

                      5) For diagram B1 loop with electronic ballast, please remove the electronic ballast first. Then connect line N and Line L to the same side socket but separately. Now your LED tube light is ready to work. And the loop has been changed into what showed in diagram B2.

                      Copyright © Fans Lighting Company Limited
                      No.1 Nanlong Road, Nanlian Community, Longgang District, Shenzhen 518116 China  URL:www.nnxwbj.com

                      本站部分圖文來源網絡,如有侵權問題請通知我們處理!
                      做網站維護
                      日本国产网曝视频在线观看_60岁女人宾馆全程露脸_3男s调教玩弄一女m文_国产纶乱视频